Browsing Department of Mechanical Engineering by Title
Now showing items 1-20 of 35
-
Aerodynamic design considerations for small-scale, fixed-pitch, horizontal-axis wind turbines operating in class 2 winds.
(, 2012-08-08)Renewable sources of energy, such as wind, are necessary to meet the growing demand as conventional energy sources are depleted. Very little research has been accomplished to improve wind turbine performance in Class 2 ... -
Applying mass and energy balances to model series and parallel fan-powered terminal units.
(2015-07-31)Performance data from four manufacturers of fan-powered terminal units was analyzed and simple models of the fan/motor power use developed. These data included two fan motors: permanent split capacitor motors with silicon ... -
Assessment of shaped film cooling holes at high density ratios for gas turbine cooling using S-PIV and PSP.
(2016-02-27)During film-hole cooling, relatively cold air is extracted from the compressor of a gas turbine engine and forced through the turbine airfoils in order to lower their surface temperatures. To investigate the effects of ... -
Characterizing hip motion during activities of daily living.
(2017-07-27)In the United States alone, 332,000 people received a total hip replacement (THR) each year [1 – need to reattach ref]. Following a total hip arthroplasty, doctors get asked by their patients if they can still do particular ... -
Convective heat transfer from realistic ice roughness distributions.
(, 2013-09-16)As supercooled water droplets impinge the surfaces of in-flight aircraft, a layer of accreted ice will form. In the initial stages of the accretion process, the ice will form as a distributed surface roughness. Ice ... -
Converting coconut husks into binderless particle board.
(2009-04-01)Coconuts grow abundantly in tropical regions, and the coconut husk is often discarded as waste. However, a new application has increased interest in developing this previously underutilized resource. Coconut pith has ... -
Damage accumulation of bovine bone under variable amplitude loads.
(2016-01-15)Stress fractures, a painful injury, are caused by excessive fatigue in bone. This study into damage accumulation in bone sought to determine if the Palmgren-Miner rule (PMR), a well-known linear damage accumulation ... -
Design and experimental testing of small-scale wind turbines.
(2011-05-12)Due to the increasing environmental and economic cost of fossil fuels, alternative sources of energy are needed. One such source is energy wind energy. Much of the current wind turbine research focuses on large-scale wind ... -
Design and implementation of a synthetic aperture radar (SAR) imaging system using an ultra-wideband (UWB) radar sensor.
(2016-04-14)This thesis documents the design and implementation of a radar imaging system. A rail system was constructed to control the location of an off-the-shelf ultra-wideband (UWB) radar along a linear path. Range imaging, ... -
The design and validation of an impinging jet test facility.
(2006-05-28)An experimental jet impingement facility was constructed with the capability of conducting a detailed analysis of the local heat transfer coefficients beneath an array of large impinging jets. The facility was validated ... -
Design and validation of new testing apparatus for testing helical compression springs under combined axial, shear, torsion, and bending loads.
(, 2011-09-14)Helical compression springs are normally used to provide a linear force response to compressive displacement. However, compression springs can be used to provide lateral force and rotational torque responses to lateral and ... -
Designing, constructing, and testing a second-generation prototype mechanical hippotherapy horse.
(, 2011-09-14)The use of horses as a means of therapy has been documented for some time. To determine why this type of therapy works and to provide a means of expanding its accessibility, a mechanical horse has been developed. Data ... -
The effect of roughness element thermal conductivity on turbulent convection.
(2011-05-12)Many flows of engineering interest occur over surfaces that exhibit roughness with thermal conductivities much lower than common metals and alloys. This is especially true of in-service gas turbine blades with surface ... -
Effects of nozzle geometry and extrudate swell on fiber orientation in Fused Deposition Modeling nozzle flow.
(2015-07-31)Fused Deposition Modeling (FDM) is a rapidly growing Additive Manufacturing (AM) technology using extruded thermoplastics to produce intricate three-dimensional parts from digital data. Adding discrete fibers to FDM filament ... -
Effects of the dynamic human body on electromagnetic wave propagation for on-body wireless communication.
(2016-04-06)Wireless Body Area Networks (WBANs) have the potential to provide long-term remote health monitoring for the prevention of impending health problems through the constant relaying of data to health professionals. In order ... -
Effects of the glenohumeral joint center on the role of the middle deltoid : implications for reverse total shoulder arthroplasty.
(, 2013-09-24)For shoulders with rotator cuff damage, the reverse shoulder replacement medializes the center of glenohumeral joint rotation, lending larger moment arms to undamaged muscles like the deltoid. The aim of this thesis was ... -
Experimental and numerical investigation of high temperature jet impingement for turbine cooling applications.
(2011-05-12)Modern gas turbine engines commonly operate at temperatures above the melting point of the turbine’s blades and vanes. Internal and external cooling of the blades is required for sustained operation and prolonged engine ... -
Experimental and numerical study on flow control using obliquely aligned elements.
(2010-06-23)The use of micro-electromechanical system devices (MEMS) have been studied extensively in literature for control of flow separation and transitioning to turbulent flow. However, there is limited information about how ... -
Experimental investigation of leading edge jet impingement with varying jet geometries and inlet supply conditions for turbine cooling applications.
(, 2012-08-08)Jet impingement is often employed within the leading edge of modern gas turbine airfoils to combat the extreme heat loads incurred within this region. This experimental investigation employs a transient liquid crystal ... -
The influence of load on kinematics of computer-simulated sagittal-plane lifting.
(2006-05-11)Researchers have shown that lifting kinematics change predictably with increased load. To test whether these kinematics patterns are intrinsic or voluntary, a computer model was developed to simulate lifting in the sagittal ...